The effect of the lamella pitch in the transverse layer on the deformability and stress distribution in a three-layer CLT panel modeled as a composite plate
https://doi.org/10.31660/2782-232X-2023-3-25-32
Abstract
Cross-laminated timber (CLT panel) and its structures are interesting for engineers and scientists due to its low installation weight, ease of fabrication, high strength and durability. However, many aspects remain under-researched. In particular, the issue of changes in deformability and bearing capacity of slabs under different variations of geometrical parameters in the layers of the structure had not been studied. We studied the effect of the pitch of the transverse layer in a three-layer CLT panel on the deformation and distribution of the resulting normal stresses. The model was a composite orthotropic plate. Because of the lack of a unified methodology for calculating layered materials with orthotropic properties in the layers, the studies were carried out by means of the SCAD+ computational complex using the finite element method. The article obtained, systematized and clearly showed the deflection and stress dependences of varying lamella pitch in the transverse layer of a three-layer CLT panel. The results provide a better understanding of the dependence of deformability and stress distributions on the variation of board pitch in the transverse layer of the slab. In the future, this will allow us to explore opportunities to optimize the design of the CLT panel in order to reduce its weight, cost, reduce resource consumption while maintaining the required characteristics.
About the Authors
M. Yu. Troshin
Orel State University named after I. S. Turgenev
Russian Federation
Russian Federation
Mikhail Yu. Troshin, Postgraduate at the Department of Building Structures and Materials
Orel
A. V. Turkov
Orel State University named after I. S. Turgenev
Russian Federation
Russian Federation
Andrei V. Turkov, Doctor in Engineering, Associate Professor, Professor at the Department of Building Structures and Materials
Orel
References
1. Ashkenazi, E. K. (1978). Anizotropiya drevesiny i drevesnykh materialov. Moscow, Lesnaya promyshlennost' Publ., 224 p. (In Russian).
2. Turkov, A. V., & Troshin, M. Y. (2022). The effect of the step of transverse layers on the deformability and stress distribution in three-layer slabs of cross-laminated timber. Arkhitekturno-stroitel'nyy i dorozhno-transportnyy kompleksy: problemy, perspektivy, innovatsii. Sbornik materialov VII Mezhdunarodnoy nauchno-prakticheskoy konferentsii, priurochennoy k provedeniyu v Rossiyskoy Federatsii Desyatiletiya nauki i tekhnologiy, November, 24-25. Omsk, Siberian state automobile and highway university Publ., 515-519 pp. (In Russian).
3. Troshin, M. Yu., & Turkov, A. V. (2023). The effect of thickness of transverse and longitudinal layers on deformability and stress distribution in three-layer panels made of cross-laminated timber. Vestnik MGSU [Monthly Journal on Construction and Architecture], 18(3), 391-400 pp. (In Russian). DOI 10.22227/1997-0935.2023.3.391-400.
4. Troshin, M. Yu., & Turkov, A. V. (2023). The effect of the step of transverse layers on the deformability and stress distribution in five-layer slabs of CLT-panels. Building and reconstruction, (3(107)), 35-41 pp. (In Russian). DOI 10.33979/2073-7416-2023-107-3-35-41.
5. Rzhanitsyn, A. R. (1986). Sostavnye sterzhni i plastinki. Moscow, Stroyizdat Publ., 316 p. (In Russian).
6. Shen, Y., Schneider, J., Stiemer, S. F., & Ren, X. (2019). Failure modes and mechanical properties of bracket anchor connections for cross-laminated-timber. MATEC Web of Conferences, No 275(11):01011. (In English). Available at: https://www.researchgate.net/publication/331709903_Failure_Modes_and_Mechanical_Properties_of_Bracket_Anchor_Connections_for_Cross-Laminated-Timber (accessed 07.08.2023). DOI 10.1051/matecconf/201927501011.
7. Christovasilis, I. P. ,Brunetti, M., Follesa, M., Nocetti, M., & Vassallo, D. (2016). Evaluation of the mechanical properties of cross laminated timber with elementary beam theories compression. Construction and building materials, No 122:202-213. (In English). Available at: https://www.researchgate.net/publication/304355276_Evaluation_of_the_Mechanical_Properties_of_Cross_Laminated_Timber_with_Elementary_Beam_Theories (accessed 07.08.2023). DOI 10.1016/j.conbuildmat.2016.06.082.
8. Bubis, A. A., Giziatullin, I. R., Petrov, I. Yu., & Khvorova, A. N. (2022). Peculiarities of behavior of cross-laminated timber (CLT) under static and dynamic loads simulating seismic impacts. Earthquake engineering. Constructions safety, (2), 62-80 pp. (In Russian). DOI 10.37153/2618-9283-2022-2-62-80.
9. Rogozhina, A. V. (2022). Calculation of the deformability of the CLT overlap panel. Ingineering journal of Don, (6(90)), pp. 329-339. (In Russian).
10. Filimonov, M. A., & Smirnov, P. N. (2022). Research of strength and elastic characteristics of Russian-made cross laminated timber slabs. Earthquake engineering. Constructions safety, (2), pp. 81-97. (In Russian). DOI 10.37153/2618-9283-2022-2-81-97.
11. Mamedov, Sh. M., Shabikova, E. G., Nizhegorodtsev, D. V., & Kazakevich, T. N. (2020). Method for calculating cross laminated timber panels. Bulletin of civil engineers, (5(82)), pp. 66-71. (In Russian). DOI 10.23968/1999-5571-2020-17-5-66-71.
12. Chebykin, A. A., Fritzler, U. A., & Kudryavtsev, S. V. (2017). Evaluation of cross section design properties for plates from cross laminated timber. Akademicheskij vestnik Uralniiproekt RAASN, (2(33)), pp. 83-85. (In Russian).
13. Pogoreltsev, A. A., Filimonov, M. A., & Smirnov, P. N. (2020). Opredelenie prochnostnyh i uprugih harakteristik drevesiny perekrestno kleenoj (DPK/CLT) i klassifikacija po klassam prochnosti: otchet o NIR. Moscow, 175 p. (In Russian).
14. Pogoreltsev, A. A., Smirnov, P. N., & Filimonov, M. A. (2020). Provedenie issledovaniy po opredeleniyu nesushchey sposobnosti stenovykh paneley i plit perekrytiya iz drevesiny perekrestno kleenoy (DPK/ CLT) i razrabotka metodiki rascheta: otchet o NIR. Moscow, 268 p. (In Russian).
Review
For citations:
Troshin M.Yu., Turkov A.V. The effect of the lamella pitch in the transverse layer on the deformability and stress distribution in a three-layer CLT panel modeled as a composite plate. Architecture, Construction, Transport. 2023;(3):25-32. (In Russ.) https://doi.org/10.31660/2782-232X-2023-3-25-32
Views:
26
Email this article 